products

TWS Charging Case Power Design: From Case Battery to Earbud Contacts

Home>Technical Support>Technical SharingTWS Charging Case Power Design: From Case Battery to Earbud Contacts

TWS Charging Case Power Design: From Case Battery to Earbud Contacts

Published: 2026-11-11  |  Author: Liwei Electronic

The power chain inside a charging case

A TWS charging case is often treated as a mechanical shell with a small PCBA, yet it carries a complete power chain: the case battery feeds the earbud charging contacts, and the case must hold its own standby current to microamp levels for months. The typical path is case lithium cell, protection board, boost or direct-path switch, pogo pin contacts, and finally the earbud charging IC. Because the case cell is usually three to five times the capacity of a single earbud, every five percentage points of conversion efficiency lost at the case side translates into a noticeable cut in the total playtime the user experiences. Three parameters must be fixed before choosing a topology: the allowed input voltage window of the earbud charger, the maximum charging current per earbud, and the standby current target with no earbuds present.

Boost or direct path

The case cell runs from 3.0V to 4.2V, while most earbud charging ICs need more than 4.5V at the input before they can regulate a constant current, which is why boost converters dominate. The cost of boosting shows up at light load: when an earbud is nearly full and current falls to tens of milliamps, a conventional PWM boost can drop below 70 percent efficiency unless PFM or burst mode is enabled to recover light-load performance. The alternative is a direct path, using a wide-input earbud charger that tolerates low voltage, with the case cell feeding it through a single low-Rds(on) MOSFET. This removes the inductor and the boost IC, cutting both cost and board area, but once the case cell falls near 3.3V the charger can only trickle a small current and the full charge takes noticeably longer. The decision follows product positioning: fast-charge models boost, thin and cost-driven models go direct with a larger case cell.

Lid detection and standby current

Lid open and close detection is normally done with a Hall switch or a mechanical contact. A Hall sensor has no wear mechanism, but the device itself draws microamps, so select on average current rather than peak. The more common failure is in firmware logic. Once the lid closes, the MCU should enter deep sleep quickly, keeping only the Hall interrupt and contact detection alive. If the Bluetooth link is kept advertising so that the earbuds reconnect the moment the lid opens, standby current jumps from tens of microamps to milliamps and the case battery is flat within a month. A staged wake-up works better: lid opens, MCU wakes, presence of earbuds is checked, and with no earbuds present the system returns to sleep after about thirty seconds.

Contacts, temperature and protection

The earbuds connect to the case through pogo pins. A fresh contact measures only tens of milliohms, but plating wear and sweat oxidation can push that to several hundred milliohms, and the resulting heat at high charging current is significant. Limit the current density per contact and place an NTC near the contacts so the charger can reduce current gradually instead of cutting off abruptly. The case cell needs its own overcharge, over-discharge and overcurrent protection, and the boost output should include short-circuit protection. Contacts shorting during earbud insertion is a frequent event, and without protection the boost switch is destroyed on the first occurrence.

FAQ

Q: Does a charging case always need a boost converter?

A: No. If the earbud charging IC accepts a wide input range from 3.0V upward and the product tolerates a longer charge time, a direct path removes the boost IC and inductor, saving cost and board area. The trade-off is that charging current falls sharply when the case battery is nearly empty, so firmware should warn the user at low case charge.

Q: Why does the case battery drain quickly even with the lid closed?

A: In most cases the sleep state is incomplete. Typical causes are a permanently enabled pull-up on the Hall sensor, an MCU internal LDO left running, or a Bluetooth module still advertising periodically. Measure the whole-case quiescent current with a microammeter and disconnect loads one at a time; a target below a few tens of microamps is achievable.

Q: Should pogo pin contacts be gold plated?

A: Yes, gold plating is recommended. Charging contacts are exposed to sweat and humidity for the life of the product, and nickel or tin finishes oxidize readily, raising contact resistance until an earbud occasionally fails to charge. The gold layer does not need to be thick, but the underlying strike layer must be dense, and the mechanical design should give the contact a small self-cleaning travel.

Key Technical Takeaways

  • Fix the earbud charging voltage window and current limit before choosing a topology
  • Validate light-load efficiency; PFM or burst mode protects standby playtime
  • Keep only the Hall interrupt alive after the lid closes
  • Limit contact current density and add an NTC near the pogo pins

About Liwei Electronic

Shenzhen Liwei Electronic Technology Co., Ltd. has focused on audio and headset electronics for over 10 years, delivering complete solutions from charging case power design to Bluetooth audio PCBA. Contact us to discuss a customized audio solution.

Keywords: TWS charging case, power design, boost converter, standby current, pogo pin contacts

Free development and design
Customized exclusive solution PCBA design
top